編號 |
中文名稱 |
英文名稱 |
BS 3900-J13-2001 |
塗料的試驗方法.塗覆粉試驗.用
雷射衍射法分析粒徑
|
Methods of test for paints - Testing of coating
powders - Particle size analysis by laser
diffraction |
BS 5381-2-1998 |
煙草和煙草製品物理特性測定方法.第2部分:用雷射光束測量儀器測定捲煙和濾嘴標準直徑
|
Methods for determination of physical properties
of tobacco and tobacco products - Nominal
diameter of cigarettes and filter rods using a
laser beam measuring apparatus |
BS 6955-1-1994 |
振動和衝擊感測器的校準.採用雷射干涉測量法對主振動的校準方法
|
Calibration of vibration and shock pick-ups -
Methods for primary vibration calibration by
laser interferometry |
BS 7334-6-1992 |
建築施工用測量儀器.第6部分:雷射儀器使用精度的測定方法
|
Measuring instruments for building construction
- Methods for determining accuracy in use of
laser instruments |
BS DD IEC/PAS 61280-2-10-2003 |
纖維光學通信子系統試驗程式.數位系統.雷射發射機的時間分辨線性調頻脈衝和α因數測量
|
Fibre optic communication subsystem test
procedures - Digital systems - Time-resolved
chirp and alpha-factor measurement of laser
transmitters |
BS EN 12254-1999 |
雷射工作場所用螢幕.安全要求和試驗
|
Screens for laser working places - Safety
requirements and testing |
BS EN 12584-1999 |
氧氣火焰切割、雷射光束切割和等離子體切割缺陷.術語
|
Imperfections in oxyfuel flame cuts, laser beam
cuts and plasma cuts - Terminology |
BS EN 15042-1-2006 |
覆層厚度測量和表面波紋表徵.採用雷射感應表面聲波法對各膜層的彈性常數、密度和厚度的測定指南
|
Thickness measurement of coatings and
characterization of surfaces with surface waves
- Guide to the determination of elastic
constants, density and thickness of films by
laser induced surface acoustic waves
|
BS EN 207-1999 |
眼睛保護.抗雷射輻射用濾光鏡和護目器(雷射護目鏡)
|
Personal eye-protection - Filters and
eye-protectors against laser radiation (laser
eye-protectors) |
BS EN 208-1999 |
眼睛防護.雷射和雷射系統調節工作用護目鏡(雷射調節護目鏡)
|
Personal eye-protection - Eye-protectors for
adjustment work on lasers and laser systems
(laser adjustment eye-protectors) |
BS EN 2266-005-2005 |
航空航太系列.通用電纜.操作溫度為-55
°C 到
200 °C .紫外雷射可印刷.產品標準
|
Cables, electrical, for general purpose
— Operating temperatures
between??-55 ℃ and 200
℃ — Part 005: UV laser
printable — Product
standard |
BS EN 2266-007-2005 |
航空航太系列.通用電纜.操作溫度為-55
°C 到
200 °C .紫外雷射可印刷多芯裝套電纜.產品標準
|
Cables, electrical, for general purpose
— Operating temperatures
between –55 ℃
and 200 ℃ — Part 007:
UV laser printable multicore jacketed cable
— Product standard
|
BS EN 2267-007-2005 |
航空系列.一般用途的電纜,電器.-55°C和260°C之間的操作溫度.DMA族、單個可列印紫外
雷射和多芯附件.產品標
|
Cables, electrical, for general purpose
— Operating temperatures
between -55 °C and 260
°C —
Part 007: DMA family, single ink-jet printable
and multicore assembly —
Product standard |
BS EN 2267-008-2005 |
航空系列.一般用途的電纜,電器.-55°C和260°C之間的操作溫度.DM族、單個可列印紫外
雷射和多芯附件.產品標
|
Cables, electrical, for general purpose
— Operating temperatures
between -55 °C and 260
°C —
Part 008: DM family, single UV laser printable
and multicore assembly —
Product standard |
BS EN 2267-009-2005 |
航空系列.一般用途的電纜,電器.-55℃和260℃之間的操作溫度.DRA族、單個可列印UV雷射和多芯附件.產品標準
|
Cables, electrical, for general purpose
— Operating temperatures
between -55 ℃ and 260
℃ — Part 009: DRA
family, single and multicore assembly —
Product standard |
BS EN 2267-010-2005 |
航空系列.一般用途的電纜,電器.-55℃和260℃之間的操作溫度.DM族、單個可列印UV雷射.產品標準
|
Cables, electrical, for general purpose
— Operating temperatures
between -55 ℃ and 260
℃ — Part 010: DR
family, single UV laser printable —
Product standard |
BS EN 2713-007-2005 |
航空航太系列.單芯和多芯電纜的一般用途.操作溫度在-55
°C 和200
°C之間.遮罩式(螺旋式)和有護套的可印
|
Aerospace series - Cables, electrical, single
and multicore for general purpose - Operating
temperatures between -55
°C and 200 °C
- Screened (spiral) and jacketed, UV laser
printable - Product standard |
BS EN 2714-007-2005 |
航空航太系列.單芯和多芯電纜的一般用途.操作溫度在-55
°C 和260
°C之間.遮罩式(螺旋式)和有護套的可印
|
Cables, electrical, single and multicore for
general purpose
— Operating temperatures
between -55 ℃ and 260
℃ — Part 007: Screened
(spiral) and jacketed, UV laser printable
— Product standard
|
BS EN 2714-011-2005 |
航空航太系列.單芯和多芯電纜的一般用途.操作溫度在-55
°C 和260
°C之間.DM族、遮罩式(螺旋式)和有護套
|
Cables, electrical, single and multicore for
general purpose
— Operating temperatures
between -55 ℃ and 260
℃ — Part 011: DM
family, screened (spiral) and jacketed, UV laser
printable — Product
standard |
BS EN 2714-012-2005 |
航空航太系列.單芯和多芯電纜的一般用途.操作溫度在-55
°C 和260
°C之間.DM族、遮罩式(麻花型)和有護套
|
Cables, electrical, single and multicore for
general purpose
— Operating temperatures
between -55 ℃ and 260
℃ — Part 012: DM
family, screened (braided) and jacketed, UV
laser printable —
Product standard |
BS EN 2714-013-2005 |
航空航太系列.單芯和多芯電纜的一般用途.操作溫度在-55
°C 和260
°C之間.DM族、遮罩式(螺旋式)和有護套
|
Cables, electrical, single and multicore for
general purpose
— Operating temperatures
between -55 ℃ and 260
℃ — Part 013: DR
family, screened (spiral) and jacketed, UV laser
printable — Product
standard |
BS EN 31253-1996 |
雷射和相關設備.雷射裝置.機械介面
|
Lasers and laser-related equipment - Laser
device - Mechanical interfaces |
BS EN 3475-706-2005 |
航空航太系列.飛行器用電纜.試驗方法.雷射可標記性
|
Cables, electrical, aircraft use
— Test methods —
Part 706: Laser markability |
BS EN 60601-2-22-1996 |
醫療電氣設備.安全專門要求.雷射診斷和治療設備規範
|
Medical electrical equipment - Particular
requirements for safety - Specification for
diagnostic and therapeutic laser equipment
|
BS EN 60825-1-1994 |
雷射產品的輻射安全性.第1部分:設備分類、要求和使用者指南
|
Safety of laser products - Equipment
classification, requirements and user's guide
|
BS EN 60825-12-2004 |
雷射產品的安全.用於資訊傳輸的自由空間光通信系統的安全
|
Safety of laser products - Safety of free space
optical communication systems used for
transmission of information |
BS EN 60825-2-2004 |
雷射產品的安全.光纖通信系統的安全
|
Safety of laser products - Safety of optical
fibre communication systems (OFCS) |
BS EN 60825-4-1998 |
雷射產品安全.雷射防護裝置
|
Safety of laser products - Laser guards
|
BS EN 60856-1993 |
50HZ/625行預錄式光反射視訊光碟錄影系統"雷射視訊光碟".PAL制規範
|
Specification for pre-recorded optical
reflective videodisk system "Laser vision" 50
Hz/625 lines - PAL |
BS EN 61040-1993 |
雷射輻射功率和能量探測器、儀錶和設備規範 |
Specification for power and energy measuring
detectors, instruments and equipment for laser
radiation |
BS EN 61096-1993 |
數位雷射唱機用放音設備特性測量方法 |
Methods of measuring the characteristics of
reproducing equipment for digital audio compact
discs |
BS EN 61280-1-4-2003 |
光纖通信子系統基本試驗程式.一般通信子系統的試驗程式.多模纖維
雷射發射機用二維近場數據的採集和整理
|
Fibre optic communication subsystem basic test
procedures - Test procedures for general
communication subsystems - Collection and
reduction of two-dimensional nearfield data for
multimode fibre laser transmitters |
BS EN 61751-1998 |
雷射電信模組.可靠性評定
|
Laser modules used for telecommunication -
Reliability assessment |
BS EN 62107-2002 |
高級雷射視訊光碟.光碟互換系統.規範
|
Super video compact disc - Disc-interchange
system-specification |
BS EN 62148-11-2004 |
纖維光學有源元件及器件.包裝和介面標準.14針調製器集成
雷射二極體發射機
|
Fibre optic active components and devices -
Package and interface standards - 14-pin
modulator-integrated laser diode transmitters
|
BS EN 62148-12-2004 |
纖維光學有源元件和器件.包裝和介面標準.帶同軸RF連接器的
雷射發射機
|
Fibre optic active components and devices -
Package and interface standards - Laser
transmitters with coaxial RF connector
|
BS EN 62149-3-2004 |
纖維光學有源元件和器件.性能標準.2.5Gbit/s調製器-集成
雷射二極體發射機
|
Fibre optic active components and devices -
Performance standards - 2,5 Gbit/s
modulator-integrated laser diode transmitters
|
BS EN 821-2-1997 |
高技術陶瓷.整體陶瓷.熱物理特性.
雷射閃爍法(或熱脈衝法)對熱擴散率的測定
|
Advanced technical ceramics - Monolithic
ceramics - Thermo-physical properties -
Determination of thermal diffusivity by the
laser flash (or heat pulse) method |
BS EN ISO 11146-1-2005 |
雷射和雷射相關設備.雷射光束寬度、發散角和束擴散率的試驗方法.無象散和簡單象散束
|
Lasers and laser-related equipment - Test
methods for laser beam widths, divergence angles
and beam propagation ratios - Stigmatic and
simple astigmatic beams |
BS EN ISO 11146-2-2005 |
雷射和雷射相關設備.雷射光束寬度、發散角和束擴散率的試驗方法.一般象散束
|
Lasers and laser-related equipment - Test
methods for laser beam widths, divergence angles
and beam propagation ratios - General astigmatic
beams |
BS EN ISO 11149-1997 |
光學和光學儀器.雷射和雷射相關裝置.非遠端通訊
雷射用的光纖連接器
|
Optics and optical instruments - Lasers and
laser related equipment - Fibre optic connectors
for non-telecommunication laser applications
|
BS EN ISO 11151-1-2000 |
雷射和雷射相關設備.標準光學元件.紫外線、可見光和近紅外光譜範圍內的元件
|
Lasers and laser-related equipment - Standard
optical components - Components for the UV,
visible and near-infrared spectral ranges
|
BS EN ISO 11151-2-2000 |
雷射和雷射相關設備.標準光學元件.紅外光譜範圍內的元件
|
Lasers and laser-related equipment - Standard
optical components - Components for the infrared
spectral range |
BS EN ISO 11252-2004 |
雷射和雷射相關設備.雷射裝置.文獻工作的最低要求
|
Lasers and laser-related equipment - Laser
device - Minimum requirements for documentation
|
BS EN ISO 11254-1-2000 |
雷射和雷射相關設備.光表面雷射導致損傷閾的測定.1-on-1試驗
|
Lasers and laser-related equipment -
Determination of laser-induced damage threshold
of optical surfaces - 1-on-1 test |
BS EN ISO 11254-2-2001 |
雷射和雷射相關設備.光表面雷射導至損傷閾值的測定.S-on-1試驗
|
Lasers and laser-related equipment -
Determination of laser-induced damage threshold
of optical surfaces - S-on-1 test |
BS EN ISO 11551-2004 |
光學和光學儀器.雷射和雷射設備
|
Optics and optical instruments - Lasers and
laser-related equipment - Test method for
absorptance of optical laser components
|
BS EN ISO 11553-1-2005 |
機械安全.雷射加工機械.一般安全要求
|
Safety of machinery - Laser processing machines
- General safety requirements |
BS EN ISO 11670-2003 |
雷射器和雷射相關設備.雷射光束參數的試驗方法.束定位穩定性
|
Lasers and laser-related equipment - Test
methods for laser beam parameters - Beam
positional stability |
BS EN ISO 11810-1-2005 |
雷射和雷射相關設備.手術布單和/或病人保護覆蓋物耐
雷射性的試驗方法和分類.基本點燃和穿透性
|
Lasers and laser-related equipment - Test method
and classification for laser resistance of
surgical drapes and/or patient protective covers
- Primary ignition and penetration |
BS EN ISO 11990-2003 |
光學和光學儀器.雷射器和相關的雷射設備.氣管柄抗
雷射性的測定
|
Optics and optical instruments - Lasers and
laser-related equipment - Determination of laser
resistance of tracheal tube shafts |
BS EN ISO 12005-2003 |
雷射器和雷射相關設備.雷射光束參數的試驗方法.偏振
|
Lasers and laser-related equipment - Test
methods for laser beam parameters - Polarization
|
BS EN ISO 13694-2001 |
光學和光學儀器.雷射和雷射設備.雷射光束能量密度分佈的試驗方法
|
Optics and optical instruments - Lasers and
laser-related equipment - Test methods for laser
beam power (energy) density distribution
|
BS EN ISO 13695-2004 |
光學和光子學.雷射和相關設備.雷射的光譜特性的試驗方法
|
Optics and photonics - Lasers and laser-related
equipment - Test methods for the spectral
characteristics of lasers |
BS EN ISO 13919-1-1997 |
焊接.電子和雷射光束焊接接頭.缺陷的品質級別導則.鋼
|
Welding - Electron and laser beam welded joints
- Guidance on quality levels for imperfections -
Steel |
BS EN ISO 13919-2-2001 |
焊接.電子和雷射光束焊接接頭.缺陷的品質分級指南.鋁及其可焊合金
|
Welding - Electron and laser beam welded joints
- Guidance on quality levels for imperfections -
Aluminium and its weldable alloys |
BS EN ISO 15367-1-2003 |
雷射和雷射相關設備.測定雷射光束波陣面形狀的試驗方法.術語及基礎領域
|
Lasers and laser-related equipment - Test
methods for determination of the shape of a
laser beam wavefront - Terminology and
fundamental aspects |
BS EN ISO 15609-4-2004 |
金屬材料焊接程式的規範和合格鑒定.焊接程式規範.雷射光束焊接
|
Specification and qualification of welding
procedures for metallic materials - Welding
procedure specification - Laser beam welding
|
BS EN ISO 15614-11-2002 |
金屬材料焊接程式的規範和合格鑒定.焊接程式試驗.電子和雷射光束焊接
|
Specification and qualification of welding
procedures for metallic materials - Welding
procedure test - Electron and laser beam welding
|
BS EN ISO 15616-1-2003 |
高品質焊接和切割用CO2雷射光束機的驗收試驗.通用原則和驗收條件
|
Acceptance tests for CO2- laser beam machines
for high quality welding and cutting - General
principles, acceptance conditions |
BS EN ISO 15616-2-2003 |
高品質焊接和切割用CO2雷射光束機的驗收試驗.靜態和動態精確度的測定
|
Acceptance tests for CO2- laser beam machines
for high quality welding and cutting -
Measurement of static and dynamic accuracy
|
BS EN ISO 15616-3-2003 |
高品質焊接和切割用CO2雷射光束機的驗收試驗.氣體流量和壓力測量儀的校正
|
Acceptance tests for CO2- laser beam machines
for high quality welding and cutting -
Calibration of instruments for measurement of
gas flow and pressure |
BS EN ISO 17526-2003 |
光學和光學儀器.雷射器和雷射相關設備.雷射器的使用壽命
|
Optics and optical instruments - Lasers and
laser-related equipment - Lifetime of lasers
|
BS EN ISO 22827-1-2006 |
Nd:YAG雷射光束焊接機器的驗收試驗.帶光纖送的機器.雷射裝配
|
Acceptance tests for Nd:YAG laser beam welding
machines - Machines with optical fibre delivery
- Laser assembly |
BS EN ISO 22827-2-2006 |
Nd:YAG雷射光束焊接機器的驗收試驗.帶光纖傳送的機器.移動機理
|
Acceptance tests for Nd:YAG laser beam welding
machines - Machines with optical fibre delivery
- Moving mechanism |
BS IEC 60825-8-2000 |
雷射產品的安全.醫療雷射設備安全使用指南
|
Safety of laser products - Guidelines for the
safe use of medical laser equipment |
BS ISO 10110-13-1998 |
光學和光學儀器.光學元件和系統圖紙的製備.第13部分:雷射輻射損壞閾值
|
Optics and optical instruments - Preparation of
drawings for optical elements and systems -
Laser irradiation damage threshold |
BS ISO 10110-17-2004 |
光學和光學儀器.光學元件和系統製圖準備.雷射輻射損害閾
|
Optics and optical instruments - Preparation of
drawings for optical elements and systems -
Laser irradiation damage threshold |
BS ISO 13320-1-2000 |
細微性分析.雷射衍射方法.一般規則
|
Particle size analysis - Laser diffraction
methods - General principles |
BS ISO 14408-1998 |
雷射外科用氣管管子的設計.標記和附加資訊要求
|
Tracheal tubes designed for laser surgery -
Requirements for marking and accompanying
information |
BS ISO 16063-11-2001 |
振動和衝擊感測器的校準方法.採用雷射干涉量度法的主要振動校準
|
Methods for the calibration of vibration and
shock transducers - Primary vibration
calibration by laser interferometry |
BS ISO 16063-13-2002 |
振動和衝擊感測器的校準方法.採用雷射干涉測量法的主要衝擊校準
|
Methods for the calibration of vibration and
shock transducers - Primary shock calibration
using laser interferometry |
BS ISO 22826-2006 |
金屬材料焊縫的破壞性試驗.雷射和電子束焊測定窄接頭硬度的試驗(維氏和努氏硬度試驗)
|
Destructive tests on welds in metallic materials
- Hardness testing of narrow joints welded by
laser and electron beam (Vickers and Knoop
hardness tests) |
BS ISO TR 11552-1998 |
雷射和與雷射相關的設備.雷射材料-加工機械.金屬切削的性能規範和基準點
|
Lasers and laser-related equipment - Laser
materials-processing machines - Performance
specifications and benchmarks for cutting of
metals |
BS ISO TR 11991-1997 |
上導氣管雷射外科手術時導氣管的管理指南 |
Guidance on airway management during laser
surgery of upper airway |
BS QC 720102-1997 |
光纖系統和子系統用帶引線的雷射二極體模數的空白詳細規範 |
Blank detail specification for laser diode
modules with pigtail for fibre optic systems and
subsystems |
編號 |
中文名稱 |
英文名稱 |